Glossy Surface
Smooth, clean outer appearance for standard filtration applications.
Three-Layer Polypropylene Depth Filtration
Melt Blown Filter Cartridges by Micron Rating, Size, Surface and End Cap
Incefiltration manufactures melt blown filter cartridges from polypropylene with good chemical compatibility. A three-layer graded pore structure provides depth filtration, high dirt holding capacity and long service life while helping prevent premature clogging. Multiple adapter joints and end configurations are available for strong installation compatibility across industrial filter housings.
Verified Product Data
Filtration MediaPP polypropylene
Micron Ratings1, 3, 5, 10, 20, 30, 60 µm
Lengths10", 20", 30", 40", 50", 60"
DiameterOD 63 / 115 mm; ID 28 / 30 mm
Melt Blown Filter Cartridge Features
The following product features are organized directly from the supplied Incefiltration product sheet.
Polypropylene Material
Made of polypropylene material with good chemical compatibility for a broad range of compatible liquids.
Three-Layer Depth Filtration
The three-layer filtration structure provides high dirt holding capacity and supports longer service life.
Graded Pore Structure
Strong structural integrity and graded pores help reduce rapid clogging during filtration.
Multiple Joint Options
A variety of adapter joints and end configurations improve installation adaptability.
Product Introduction & Construction
The cartridge uses polypropylene filtration media, optional PP or stainless steel center support, polypropylene end caps and hot-melt-welded connections without adhesive.
End CapPP polypropylene with multiple interface options
Filtration MediaThree-layer graded PP melt blown media
Center CorePP polypropylene or stainless steel
Verified Material & Construction Data
Filtration MediaPP polypropylene
Center CorePP polypropylene / stainless steel
End CapPP polypropylene
O-Rings / GasketsSilicone rubber, EPDM rubber, NBR rubber, Viton rubber
Connection ProcessSealed by hot melt welding, no adhesive
Typical ApplicationsSeawater RO pretreatment, condensate filtration, food and beverage, biopharmaceuticals, microelectronics, chemicals and petroleum
100% Polypropylene
All-polypropylene media supports broad use in compatible industrial liquids.
CFR 21 Options
Suitable material configurations can be selected to comply with CFR 21 requirements where applicable.
No Adhesive
Hot melt welding forms the connection without adhesive.
Melt Blown Cartridge Appearance Options
The supplied product sheet shows six available surface appearances. Replace each placeholder with the corresponding real cartridge photograph.
Orange Peel Surface
Textured outer surface with an orange-peel-like appearance.
Pressure Point Surface
Point-pattern surface treatment designed to improve structural stability.
Embossed Surface
Embossed outer pattern for a reinforced and distinctive surface.
Grooving Surface
Grooved construction that increases the effective external surface area.
Furry Surface
Loose-fiber outer appearance for selected depth-filtration configurations.
Melt Blown Filter Cartridges by Micron Rating
Available filtration accuracy follows the supplied product specification sheet.
Fine Filtration
For fine suspended-particle removal and protection before sensitive downstream filtration.
1 µm3 µm5 µm
General Process Filtration
Suitable for water, chemicals, food and beverage and process-liquid clarification.
10 µm20 µm30 µm
Coarse High-Flow Filtration
Designed for larger particle removal and lower pressure drop.
60 µm
Melt Blown Filter Cartridges by Size
Match nominal length, outside diameter and inside diameter to the existing filter housing.
Cartridge Length
The supplied product sheet lists six nominal cartridge lengths.
10 inch20 inch
30 inch40 inch
50 inch60 inch
Outside Diameter
Standard and large-diameter melt blown cartridge options.
63 mm OD115 mm OD
Inside Diameter
Select the inside diameter according to the housing support structure.
28 mm ID30 mm ID
Melt Blown Filter Cartridge End Cap Options
The product sheet shows nine commonly used interfaces. Replace each placeholder with the corresponding real end-cap photograph.
Flat End Cap
Flat interface for standard cartridge housing configurations.
222 End Cap
Double O-ring adapter for secure sealing.
High 222 End Cap
Extended 222 adapter for taller connection requirements.
226 End Cap
Bayonet-style adapter for compatible housings.
215 End Cap
215 interface for selected filtration housings.
Threaded End Cap
Threaded adapter for screw-in installation.
Triangle Tip
Triangle fin for alignment and stabilization.
Semi-Winged Tip
Semi-winged fin for positioning in compatible housings.
Flat Peak Cover
Flat peak closed-end cover for selected designs.
Melt Blown Filter Cartridge Specifications
The following specifications are taken directly from the supplied Incefiltration product sheet.
| Category | Specification Item | Verified Product Data |
|---|---|---|
| Product Size | Filtration Accuracy | 1 µm, 3 µm, 5 µm, 10 µm, 20 µm, 30 µm, 60 µm |
| Length | 10", 20", 30", 40", 50", 60" | |
| Diameter | OD 63 mm / 115 mm; ID 28 mm / 30 mm | |
| End Cap Type | Port / Interface Options | 215, 222, High 222, 226, Triangle Tip, Semi-Winged Tip, Flat Peak Cover and Flat |
| Operating Conditions | Maximum Temperature | 70°C |
| Maximum Differential Pressure | 2.0 bar at 21°C | |
| Recommended Change-Out ΔP | 2.4 bar | |
| Note | Hot Water / Steam Sterilization | Stainless steel insert option is required for cartridges intended for hot water sanitization or steam sterilization. |
Pure Water Flow Rate Test Data
The supplied chart compares pressure drop against water flow for 1, 3, 5, 10, 30 and 60 µm melt blown cartridges.
Pressure Drop Trend by Micron Rating
1 µm
3 µm
5 µm
10 µm
30 µm
60 µm
The page reproduces the performance trend shown in the supplied sheet. Actual values depend on cartridge length, surface finish, center support, liquid viscosity, temperature and housing conditions.
Typical Melt Blown Cartridge Applications
The application categories below follow the supplied product introduction.
Seawater RO Pretreatment
Suspended-solids removal before reverse-osmosis and desalination systems.
Condensate Filtration
Particle removal from compatible condensate and utility-water systems.
Food & Beverage
Process-water and compatible liquid filtration using polypropylene construction.
Biopharmaceutical
Economical pre-filtration before finer cartridge and membrane stages.
Microelectronics
Particle removal from compatible process water and manufacturing liquids.
Chemical Industry
Filtration of compatible acids, alkalis and process chemicals.
Petroleum Industry
Particle removal from compatible petroleum and industrial process liquids.
OEM Filtration Systems
Custom sizes, surfaces and interfaces for filtration equipment manufacturers.
Custom Melt Blown Filter Cartridge Service
Incefiltration supports the verified micron range, six surface appearances, listed dimensions, PP or stainless steel center cores, multiple end caps, gaskets and private packaging.
Confirm Working Liquid
Provide liquid composition, viscosity, temperature, pressure and contaminant loading.
Select Micron & Surface
Choose 1, 3, 5, 10, 20, 30 or 60 µm and the required surface appearance.
Match Housing Interface
Confirm length, OD, ID, center core, end cap, seal and installation method.
Sample & Production
Support sample approval, OEM labels, bulk orders and export packaging.
Need a Custom Melt Blown Filter Cartridge?
Send your micron rating, dimensions, surface appearance, end-cap photo, liquid and operating conditions.
Melt Blown Filter Cartridge FAQ
Common questions based on the verified product data.
What micron ratings are available?
The verified available ratings are 1, 3, 5, 10, 20, 30 and 60 µm.
What surface appearances can be supplied?
Glossy, Orange Peel, Pressure Point, Embossed, Grooving and Furry Surface options are shown in the product sheet.
What cartridge sizes are available?
Lengths include 10, 20, 30, 40, 50 and 60 inches. Available diameters are OD 63 or 115 mm and ID 28 or 30 mm.
Which end cap interfaces are available?
Flat, 215, 222, High 222, 226, Threaded, Triangle Tip, Semi-Winged Tip and Flat Peak Cover options are available.
What are the operating limits?
The supplied sheet lists a maximum temperature of 70°C, maximum differential pressure of 2.0 bar at 21°C and recommended change-out differential pressure of 2.4 bar.
Request a Melt Blown Filter Cartridge Quote
Send the required micron rating, size, surface appearance, center core and end cap.